Pro PNP Plug And Play ECU – BMW E36 328i/M3 1996-1999, E36..

Description

MS3Pro Plug and Play for 1996-1999 BMW M3 E36 Replace your “Siemens MS41” DME with a tunable racing ECU! MS3Pro Plug and Play for 1996-1999 BMW M3 E36 and 1997-2000 BMW Z3M allows tuning your E36/7 with a laptop to handle any mods you can throw at these engines! MS3Pro Plug and Play for 1996-1999 BMW M3 E36 fits the following applications. Confirmed for US market vehicles: 1996-1999 BMW E36 328i with M52 motor and manual transmission 1996-1999 BMW E36 M3 with S52 motor and manual transmission 1995-1998 BMW E39 528i with M52 motor and manual transmission 1995-1998 BMW E38 728i with M52 motor and manual transmission 1997-1998 BMW Z3 2.8i with M52 motor and manual transmission (Not compatible with the later M52TU motor) 1997-2000 BMW Z3M with S52 motor and manual transmission **European market M3 compatibility is not confirmed at this point. **South African market 1997-2000 Land Rover Defender with M52 likely to work, but compatibility is not confirmed at this point. MS3Pro Plug and Play for 1996-1999 BMW M3 E36 Model Features: Fully Plug and Play Installation – No wiring required for basic functionality. The ONLY aftermarket M52 ECU on the market that supports the stock BMW camshaft position sensor – NO Hall sensor retrofit needed!!! Maintains functionality of the factory ACS+T traction control system Maintains functionality of the factory Econometer/MPG gauge on the dashboard Base map is pre-loaded to help your engine start on the first turn of the key Real time tuning and data logging with a laptop connection 8 GB internal data logging with built in SD card Supports most aftermarket wideband sensors Fully Tunable Engine Control! 16×16 Fuel Tables allow high resolution tuning 16×16 Ignition Tables Multiple Acceleration enrichment strategies Closed Loop Idle Speed Control Air Conditioner Control 6 sequential fuel injector channels with individual trim tables Onboard high impedance injector drivers Allows removal of stock MAF sensor VANOS control Advanced Feature Set (Included!) 12×12 Air Fuel Ratio Target Tables for use with wide band O2 sensor for precise tuning and table trim. Multiple traction control strategies Built-in 3-step rev limiter / launch control with flat shift and burnout rev limiter Time based timing / boost increase after launch Real time barometric correction Internal 4-bar MAP sensor reads up to 44PSI of boost Overboost protection Closed loop boost control (Requires DIYAutoTune.com EBC solenoid kit) CO2 based boost control Set boost by RPM and throttle, ground speed, or gear Rally style anti lag Water injection control – on/off or variable Knock sensor input with adjustable sensitivity, crank angle windowing, and more Table switching input. Change fuel and spark maps on the fly for different fuels, nitrous activation, etc. Input for flex fuel sensor – switch between E85 and gasoline on the fly! CANBus connector allows interconnection of other MegaSquirt-compatible devices for additional functions (EGT Input, Automatic Transmission Controller, Additional Sensors…..the possibilities are limitless! What you get in the box: MS3Pro Plug and Play for 1996-1999 BMW M3 E36 ECU RS232 tuning cable 20 Pin Options Connector Tuning Software and Documentation on USB memory stick with two base maps included: Stock M52 Stock S52 6′ Vacuum Hose for MAP Signal and ‘T’ fitting ECU mounting brackets Registered version of TunerStudio and MegaLog viewer included Direct replacement for: Siemens MS41.x DME Not compatible with: M52TU DME Siemens MS42 If your ECU / DME has a different part number, please contact us to see if it is compatible with MS3Pro Plug and Play for 1996-1999 BMW M3 E36 & 1997-2000 BMW Z3M.